Control panel section contains screw,8-18ab x 0.455 switch,temp selector ,7 position screw,pan head ,6-20ab x 0.750 ,#8 comb head dispenser assy thermistor,w/hose & clamp clamp cover,bleach knob,rotary ,white latch,disp drawer hdl siphon. Cabinet/top components are shield,overflow screw,pan head ,8-18ab x 0.375 screw,flat head ,10-16 x 0.600 ,quadrex control board,temperature ,automatic hose,water inlet ,cold screw,10-16ab x 0.375 screw,hex washer hd ,8-18ab x 1.125 hose,drain valve,water ,115 v screw,quad pan head ,10-16 x 0.312. Motor/tub is composed of sleeve,protector ,upr spring hook screw,10-16ab x 0.375 tube assy,air pressure ,w/air chamber pin,shock mtg. filter,pump spring,boot retainer shell,outer tub ,rear ,with bearing pulley,drum drive ,large ,rear sleeve,protector ,lwr spring hook shell,outer tub ,front. Wiring diagram components are . Wiring diagram parts include .
What is the Frigidaire Front Loading Washer GLTF1570FS2 tub capacity?
Tub Capacity as per Manufacturer Specifications (in cubic feet):
The manufacturers began using cubic feet capacity numbers only recently.
Previously, they used relative terms such as "Large" or "Extra Capacity" or laundry weight (e.g. "16 lbs per load")
which did not take into account different fabric weight and volume. Others referred to capacity in
terms of water used. Even washers available today do not have capacity written in the manual because the same manual
can be used across multiple models. Once the washer is no longer sold, the sales literature is discarded
and capacity information often lost.
Analyzing washers and their components, searching through old technical information and sales literature, and
determining their capacity is a labor intensive and time-consuming task and we are far from finished.
A small charge will help us continue our research.
Consider this: if you were to spend more than four minutes looking for tub capacity on the internet, you
would be earning LESS than minimum wage.
Calculate Front Load Washer Tub capacity
This is a geometric method to calculate tub capacity based on the cylinder volume formula.
Unfortunately, the value could be as much as 25% off from the manufacturer stated capacity.
Why? Because the tub is not exactly a cylinder. The edge where bottom connected to the wall
is not at 90 degree angle but smooth and rounded. The water line is not clearly marked and
the bottom is not always flat. Finally, an agitator also takes capacity away from the tub.
This method can be used as a crude estimate but we do not recommend using it for comparisson
when shopping for a new washer.
To determine your front load washer tub capacity please take two simple measurements:
1. Use the ruler to measure the depth of the tub (indicated by the red line on the diagram)
2. Now find the distance accross the tub, the diameter (the green line on the diagram). Note that some horizontal tubs have a narrow opening.
In this case make the measurements INSIDE the tub.
Tub Depth: in. Tub Diameter: in.
The Frigidaire Front Loading Washer GLTF1570FS2 tub capacity is ... cubic feet.
DOE (Department of Energy) vs. I.E.C. (International Efficiency Consortium) tub capacity values
The tub capacity calculator provides result in the DOE cubic feet which are CONVENTIONAL, i.e. normal cubic feet.
The front loading appliance manufacturers prefer to use IEC cubic feet in their specification. IEC capacity
in a front loader is the equivalent of the laundry size of a top loading washer and usually result in a higher number.
For instance, a 4.7 cu. ft EC capacity transaltes into 4.1 conventional cu. ft for some washers and into 4.2 cu. ft for others.
There is no simple multiplier that can be applied to an IEC value to translate it into DOE capacity.
Make sure to use the manufacturer's part number when ordering a replacement.