Controls & backsplash section contains housing socket pkg 4 p1n scr 8-18 hi/lo 5/8 hose pressure switch housing terminal board asm mounted end cap lh wh term hsng - solenoid hose inlet asm backsplash asm filter power line. Cabinet, cover & front panel components are bushing hinge (single) scr 8-18 b ihw 1 s bumper hinge bracket apron front leg leveling wire tie bumper lid shipping bar asm strap bar self leveling. Tub, basket & agitator section includes flat washer hose drain asm washer tub bearing balance ring asm hose flood seal tub cover tub hose drain inlet clamp - tub gasket flood head. Suspension, pump & drive components parts are counterweight scr 1/4-20 b hxw 3.9 sns rod & spring asm pulley driven belt scr 1/4-20 tpt 1h 1/2 sn belt installation tool socket rod support pump motor/inverter electroni. Controls & backsplash parts include knob asm hose pressure switch funnel shower head switch pressure pm sheet mini manual housing terminal valve triple water owners manual backsplash asm probe sensor atc. Cabinet, cover & front panel is composed of funnel bleach housing terminal bushing hinge (single) protector lid switch screw 8-32x3/8 grd scr screw magnet housing asm scr 8-16 b flp .625 zn pin alignment clip locking. Tub, basket & agitator components are bearing tub scr 1/4-20 mch hxw 5/8 s hose drain inlet cover tub clamp hose hose drain asm scr 10-32 b trt-25 5/8 coupling pulsator dispenser asm fs ring split. Suspension, pump & drive components is composed of pump belt pulley driven shaft and tube asm counterweight scr 1/4-20 b hxw 3.9 sns scr 1/4-20 b hxw 3/4 sns leg and platform asm rod & spring asm nut pulley.
What is the GE HydroWave Washer with Infusor Agitator WPRE6150K1WT tub capacity?
Tub Capacity as per Manufacturer Specifications (in cubic feet):
The manufacturers began using cubic feet capacity numbers only recently.
Previously, they used relative terms such as "Large" or "Extra Capacity" or laundry weight (e.g. "16 lbs per load")
which did not take into account different fabric weight and volume. Others referred to capacity in
terms of water used. Even washers available today do not have capacity written in the manual because the same manual
can be used across multiple models. Once the washer is no longer sold, the sales literature is discarded
and capacity information often lost.
Analyzing washers and their components, searching through old technical information and sales literature, and
determining their capacity is a labor intensive and time-consuming task and we are far from finished.
A small charge will help us continue our research.
Consider this: if you were to spend more than four minutes looking for tub capacity on the internet, you
would be earning LESS than minimum wage.
Calculate Top Load Washer Tub capacity
This is a geometric method to calculate tub capacity based on the cylinder volume formula.
Unfortunately, the value could be as much as 25% off from the manufacturer stated capacity.
Why? Because the tub is not exactly a cylinder. The edge where bottom connected to the wall
is not at 90 degree angle but smooth and rounded. The water line is not clearly marked and
the bottom is not always flat. Finally, an agitator also takes capacity away from the tub.
This method can be used as a crude estimate but we do not recommend using it for comparisson
when shopping for a new washer.
Determine your top load washer tub capacity by taking two simple measurements:
1. Use the ruler to measure the depth of the tub (indicated by the red line on the diagram)
2. Now find the distance accross the tub, the diameter (the green line on the diagram). Note that some tubs are narrow
on top. In this case make the measurements INSIDE the tub.
Tub Depth: in. Tub Diameter: in.
The GE HydroWave Washer with Infusor Agitator WPRE6150K1WT tub capacity is ... cubic feet.