Top and cabinet parts components are bearing, lid hinge (2) energy guide screw, 10-16 x 3/8 (4) top hinge, lid (l. h.) screw, lid hinge mounting (4) clip, top & cabinet & rear panel (2) switch, lid manual (washer) do-it-yourself bumper, lid (2). Control panel parts section includes cap, end (r.h.) (includes item 8) screw, 8-18 x 3/8 bracket, control screw, timer mounting switch, water temperature switch, water level knob, control screw, ground dial and guard, timer cap, end (l.h.) (includes item 8). Rear panel parts components are u-bend, drain hose hose, water inlet (hose (inlet), blue) screw, strap to panel (8-18 x 3/8) clamp, hose valve, water inlet w/vacuum break & thermistor strap, console (2) cord, power (includes item 20) clamp, hose clamp, hose panel, rear. Agitator, basket and tub parts components are clip, pressure switch hose balance ring cam, driven spacer-thrust bearing, cam driven screw & washer (5/16-24 x 1) basket & balance ring nut, spanner gasket, tub ring hose, pressure. Brake, clutch, gearcase, motor and pump parts components are screw, 10-16 x 5/8 (2) clutch (complete) pump (complete) cap, clutch spring (2) screw, gearcase to base (3) grommet, motor (4) coupling, motor seal ring, retainer band & lining, clutch (includes items 7 & 8). Machine base parts is composed of spring, suspension (3) link, leveling mechanism (2) spring, leveling mechanism ring, sound deadening retainer, suspension spring (3) bracket, spring outer (l.f.) pin, knurled foot, front (2) nut, 3/8-16 (2) pad, plate. Wiring harness parts components are clip, harness clip, harness connector (t.p.a.) (3-circuit) plug (t.p.a) (3-circuit) (pressure switch) clip, harness plug, terminal (3-way) clip, harness (push-in) receptacle, terminal (3-way) clip, harness (half-harness) retainer, harness. Brake and drive tube parts parts include driver, brake cam sleeve, brake spring ring, retaining ring, retaining brake and drive tube (complete) shoe, brake (2) tube, basket drive (includes illus. 3, 4, 5 & 9) cap, brake spring (2) spring, brake ring, thrust. Gearcase parts, optional parts (not included) components are sealer, gasket (.20 fl. oz.) (6 ml) paint, bulk (1 qt.) (white (uncut)) gearcase (complete) inlet hoses, 6 ft. (two black hoses w/one straight end & one 90 degree end & 4 rubber washers) screw, gearcase cover, mounting (8) (10-24 x 3/8) neutral assembly inlet hoses, 6 ft. (two braided hoses w/one straight end & one 90 degree end & 4 rubber washers) siphon break kit lubricant (use only in brake shoe assembly on roller and pin) shaft, agitator (includes 11 and 29).
What is the Kenmore Top Load Washer 11029422801 tub capacity?
Tub Capacity as per Manufacturer Specifications (in cubic feet):
The manufacturers began using cubic feet capacity numbers only recently.
Previously, they used relative terms such as "Large" or "Extra Capacity" or laundry weight (e.g. "16 lbs per load")
which did not take into account different fabric weight and volume. Others referred to capacity in
terms of water used. Even washers available today do not have capacity written in the manual because the same manual
can be used across multiple models. Once the washer is no longer sold, the sales literature is discarded
and capacity information often lost.
Analyzing washers and their components, searching through old technical information and sales literature, and
determining their capacity is a labor intensive and time-consuming task and we are far from finished.
A small charge will help us continue our research.
Consider this: if you were to spend more than four minutes looking for tub capacity on the internet, you
would be earning LESS than minimum wage.
Calculate Top Load Washer Tub capacity
This is a geometric method to calculate tub capacity based on the cylinder volume formula.
Unfortunately, the value could be as much as 25% off from the manufacturer stated capacity.
Why? Because the tub is not exactly a cylinder. The edge where bottom connected to the wall
is not at 90 degree angle but smooth and rounded. The water line is not clearly marked and
the bottom is not always flat. Finally, an agitator also takes capacity away from the tub.
This method can be used as a crude estimate but we do not recommend using it for comparisson
when shopping for a new washer.
Determine your top load washer tub capacity by taking two simple measurements:
1. Use the ruler to measure the depth of the tub (indicated by the red line on the diagram)
2. Now find the distance accross the tub, the diameter (the green line on the diagram). Note that some tubs are narrow
on top. In this case make the measurements INSIDE the tub.
Tub Depth: in. Tub Diameter: in.
The Kenmore Top Load Washer 11029422801 tub capacity is ... cubic feet.