Front cover components are . Top and cabinet components are bearing, lid hinge (2) hinge, lid (l.h.) pad, lid hinge (2) hinge, lid (r.h.) nut, push-in (2) bumper, lid (2) white bumper, lid hinge strike, lid switch rivet, serial nameplate. Rear panel is composed of clamp, hose hose, drain (5 1/2 ft.) strain relief, power cord shield, suds (alt.) hose, water inlet (2) hinge, console (2) cord, power screw, 10-16 x 1/2 hose, pump to tub. Control panel components are cap, end (r.h.) trim, endcap (l.h.) timer, control 60 hz. (motor not a service part) cap, end (l.h.) nut, push-in clip, knob bracket, control switch, water level screw, ground 10-24 x 3/8 knob, water level. Brake, clutch, gearcase, motor and pump parts include motor, main drive capacitor, motor start clamp, capacitor band & lining, clutch (includes illus. 7 & 8) ring, spin tube support shield, tub to motor screw, capacitor mounting pump (complete) coupling, motor and isolation cap, clutch spring (2). Agitator, basket and tub section contains gasket, tub ring screw & washer (5-16-24 x 1) agitator cap, barrier hose, pressure switch cam, agitator lock, filter tub gasket, centerpost clothes mover. Miscellaneous parts are nut, lock (2) (3/8-16) clamp, hose miscellaneous parts bag washer, inlet hose (1-1/16 x 5/8) (4) foot, front (2). Machine base section contains screw, bracket mounting (10-16 x 5/8) (6) link, leveling mechanism (2) pin, knurled bracket, spring outer (l.f.) seal, centerpost (3) support & brake, tub base assembly (includes illus, 6, 7, 8, 9, 18 & 26) nut, lock (3/8-16) (2) retainer, suspension spring centerpost bearing kit (includes illus. 13, 14 & 23). Wiring harness components are terminal, female clip, harness block, disconnect (timer) (black) terminal, female block, disconnect (motor) wiring harness & pressure switch hose terminal, male clip, harness protector, harness receptacle, terminal (lid switch). Gearcase parts include pinion, spin (includes illus. 25) bearing, thrust follower, cam cam, agitator shaft, agitator gear, agitator actuator, shift washer, cam thrust shaft, agitator (complete) seal, gearcase cover. Brake and drive tube parts are cap, brake spring (2) driver, brake cam cam, brake release sleeve, cam sleeve, brake spring t tube, basket drive (includes illus. 3, 4, 5 & 9) seal, oil ring, retaining ring, thrust.
What is the KitchenAid Top Load Washer KAWE460WWH3 tub capacity?
Tub Capacity as per Manufacturer Specifications (in cubic feet):
The manufacturers began using cubic feet capacity numbers only recently.
Previously, they used relative terms such as "Large" or "Extra Capacity" or laundry weight (e.g. "16 lbs per load")
which did not take into account different fabric weight and volume. Others referred to capacity in
terms of water used. Even washers available today do not have capacity written in the manual because the same manual
can be used across multiple models. Once the washer is no longer sold, the sales literature is discarded
and capacity information often lost.
Analyzing washers and their components, searching through old technical information and sales literature, and
determining their capacity is a labor intensive and time-consuming task and we are far from finished.
A small charge will help us continue our research.
Consider this: if you were to spend more than four minutes looking for tub capacity on the internet, you
would be earning LESS than minimum wage.
Calculate Top Load Washer Tub capacity
This is a geometric method to calculate tub capacity based on the cylinder volume formula.
Unfortunately, the value could be as much as 25% off from the manufacturer stated capacity.
Why? Because the tub is not exactly a cylinder. The edge where bottom connected to the wall
is not at 90 degree angle but smooth and rounded. The water line is not clearly marked and
the bottom is not always flat. Finally, an agitator also takes capacity away from the tub.
This method can be used as a crude estimate but we do not recommend using it for comparisson
when shopping for a new washer.
Determine your top load washer tub capacity by taking two simple measurements:
1. Use the ruler to measure the depth of the tub (indicated by the red line on the diagram)
2. Now find the distance accross the tub, the diameter (the green line on the diagram). Note that some tubs are narrow
on top. In this case make the measurements INSIDE the tub.
Tub Depth: in. Tub Diameter: in.
The KitchenAid Top Load Washer KAWE460WWH3 tub capacity is ... cubic feet.