Partial list of this Whirlpool Super Capacity Top Load Washer components
(for additional details, please see All Parts & Diagrams
Top and cabinet parts parts are harness, jumper switch, lid bearing, lid hinge (2) clip, top & cabinet & rear panel (2) installation instructions (spanish) top feature sheet (english/french) screw, ground energy guide hinge, lid (l.h.). Controls and rear panel parts parts are hose, flowmeter to tub ring screw, ground clamp, hose knob, timer hose, pump to tub (includes item 30) screw, 8-18 x 3/8 clamp, hose cap, end (l.h.) (includes item 19) pad, rear panel bracket, control. Agitator, basket and tub parts components are screw & washer (5/16-24 x 1) bearing-driven cam gasket, centerpost clip, pressure switch hose clothes mover washer, agitator dispenser dog, agitator clutch (4) hose, pressure switch seal, tub ring. Brake, clutch, gearcase, motor and pump parts parts include motor, main drive pump (complete) coupling, motor & isolation cap, clutch spring (2) switch, main drive motor washer, spin tube thrust shield, motor retainer, pump (2) screw, gearcase to base (3) capacitor. Machine base parts parts include foot, rear (2) screw, bracket mounting (10-32 x 5/8) seal, centerpost (3) seal, centerpost support & brake, tub pad, plate centerpost bearing kit (includes items 10, 11 & 19) retainer, suspension spring bracket, spring outer (l.f.) ring, sound deadening. Wiring harness parts section includes clip, harness retainer, (suds models) block, disconnect (use term. 352088) connector (t.p.a.) (3-circuit) (lid switch) clip, harness clip, harness protector e.t.c. control block, disconnect (motor 2 speed) (use term.352088) clip, harness. Brake and drive tube parts is composed of ring, retaining cap, brake spring (2) driver, brake cam spring, brake shoe, brake (2) brake and drive tube (complete) lubricant (use only in brake shoe assembly on roller & pin) cam, brake release ring, thrust sleeve, brake spring. Gearcase parts, optional parts (not included) components are washer kit, thrust drain hose extension kit inlet hoses, 5 ft. (two braided hoses w/straight ends & 4 rubber washers) sealer, gasket (.20 fl. oz.) (6 ml) inlet hoses, 5 ft. (one red hose & one blue hose w/straight ends & 4 rubber washers) ring, retaining (2) paint, touch-up (1/2oz.) (white) spring, agitate cover, gearcase washer, agitate gear. Top and cabinet parts section contains following may be purchased do-it-yourself repair manuals installation instructions (english/french) energy guide filter, rfi wiring diagram lid (red) manual, washer top (white) clip, top & cabinet & rear panel (2) use & care guide (english/french). Controls and rear panel parts is composed of pad, rear panel harness, wiring bracket, control clamp, hose knob, control cap, end (l.h.) (includes item 19) (white) clip, console valve, water inlet screw, ground clamp, hose. Agitator, basket and tub parts parts are screw & washer (5/16-24 x 1) agitator (complete) bearing-driven cam washer, agitator agitator block, basket drive cam, driven dispenser dog, agitator clutch (4) hose, pressure switch. Brake, clutch, gearcase, motor and pump parts components are spring, clutch pump (complete) band & lining, clutch (includes items 7 & 8) switch, main drive motor clutch (complete) coupling, motor & isolation gearcase (complete) brake & drive tube (complete) motor, main drive retainer, pump (2). Machine base parts section contains bracket, spring outer (2) foot, rear (2) spring, leveling mechanism bracket, spring outer (l.f.) pad, plate pad, base spring, counterweight foot, front (2) pin, knurled link, leveling mechanism (2). Wiring harness parts is composed of block, disconnect (12-way) clip, harness (push-in) timer, block disconnect (natural) receptacle, terminal (3-way) block, connector (natural) protector clip, harness (half-harness) clip, harness block, disconnect receptacle (6-way). Brake and drive tube parts components are brake and drive tube (complete) cam, brake release sleeve, cam driver, brake cam cap, brake spring (2) sleeve, brake spring ring, retaining ``t`` bearing, spin tube ring, retaining spring, brake. Gearcase parts, optional parts (not included) parts include seal, thrust plug hose screen (package of 2) retainer, spring rack, connecting paint, touch-up (1/2oz.) (magna red gloss) spring, agitate inlet hoses, 5 ft. (two black hoses w/straight ends & 4 rubber washers) paint, touch-up (1/2oz.) (white) drain protector seal, spin pinion.