Partial list of this Whirlpool Laundry Center components
(for additional details, please see All Parts & Diagrams
Washer/dryer control panel parts parts are clip, harness (2) connector (motor-dryer) switch, pressure buzzer, mini knob, control (2) gasket, console guide, use & care bracket, control (includes illus. 2) end cap (lh) end cap (rh). Dryer front panel and door parts section contains catch, door hinge & pin, door (2) screw, door switch mounting (2) screw, 10-16 x 1/2 screw, 8-18 x 1/2 panel, toe nut, push (4) clip, door hinge (2) retainer, toe panel (2) seal, door. Dryer cabinet and motor parts parts are clip, front panel (2) bracket, idler clip, ground spacer (2) lever-snap switch wire, broken belt switch cove, transition panel (black) panel, side (l.h.) bracket, bulkhead panel, rear. Dryer bulkhead parts parts include screw, 10-16 x 1/2 shaft, roller screw, 10-16 x 13/16 baffle, drum (3) lint duct assembly (includes illus. 7 & 13) seal, outlet housing door, lint screen bulkhead, rear thermostat, internal-bias nut (2). Dryer support and washer harness parts components are screw, 10-16 x 1/2 screw, 10-16 x 1/2 hose, pressure switch shield, thermostat connector, h-pod channel assembly (left hand side) shield, front shield, harness screw wire. Washer top and lid parts components are screw and washer lid screw, 10-16 x 1/2 switch, lid lid retainer hinge, l.h. locator, top clip, wire (4) nut, push-in (2) clip, grounding. Washer cabinet parts section includes clip, front panel (2) hose, drain connector, hose clamp, hose bracket, valve bracket, base foam foot, front (2) plug, top to cabinet (2) clip, spring top (2). Brake, clutch, gearcase, motor and pump parts components are cap, clutch spring (2) clutch (complete) plate, motor mount to gearcase switch, main drive motor gearcase (complete) motor, main drive capacitor, motor start screw, 10-16 x 3/8 ring, spin tube support shield, tub to motor. Machine base parts parts include spring, counterweight bearing, centerpost (2) retainer, suspension spring centerpost bearing kit (includes illus. 13, 14 & 23) pad, plate base assembly (includes illus. 11 & 18) seal, centerpost (3) spring, suspension (3) seal, centerpost bracket, spring outer (l.f.). Agitator, basket and tub parts is composed of spacer, thrust cam driven screw & washer dog, agitator (4) basket gasket, centerpost agitator tub dispenser block, drive. Gearcase parts parts include ball, bearing (includes 17) bottom and pinion, gearcase bearing, thrust (includes 18) retainer, spring (2) screw, gearcase cover mounting (8) (10-24 x 3/8) neutral assembly cam, agitate (includes 13) ring, retaining seal, thrust plug washer, intermediate. Brake and drive tube parts parts are driver, brake cam sleeve, brake spring lubricant (use only in brake shoe assembly on roller & pin) sleeve, cam cap, brake spring (2) ring, thrust brake and drive tube (complete) spring, brake tube, basket drive (includes illus. 3, 4, 5 & 9) ring, retaining. Water system parts section contains hose, corrugated plastic drain (10 ft.) (not included) connector, straight u-bend hose, corrugated plastic drain (6 1/2 ft.) (for fsou & twin-twin) sleeve kit, plastic drain hose (contains 2 sleeves) hose, inlet (2) hose, corrugated plastic drain (5 1/2 ft.) connector kit, plastic drain hose siphon break kit (not included) clamp, hose. Miscellaneous parts, optional parts (not included) section contains clamp, hose (upper drain) paint, bulk (1 qt.) (biscuit (uncut)) paint, bulk (1 qt.) (white (uncut)) paint, pressurized spray (12 oz.) (biscuit) paint, pressurized spray (12 oz.) (primer, gray) paint, touch-up (1/2oz.) (biscuit) sealer, gasket (.20 fl. oz.) (6 ml) washer, inlet hose paint, pressurized spray (12 oz.) (white) lubricant (use only in brake shoe assembly on roller and pin).