Did you know that many appliances bearing the same name are produced
by different manufacturers? For example, a lot of Kenmore
dishwashers are made by Whirlpool and Frigidaire, while
certain Maytag washers were produced by Samsung.
Service and repair manuals often refer to the
original base model before it was rebranded.
After your payment is complete you will be redirected to the document retrieval section.
Parts List & Diagrams:
Most modern browsers and operating systems are able to display PDF documents. If you operate an older device,
you will need Adobe Acrobat Reader to view these documents. Adobe Acrobat Reader is available as
a free download.
Carl (Trinidad & Tobago) wrote on November 4, 2017
Clothes remaining wet
I have this unit for over 16years. It has performed exceptional, and the body is in good condition. Recently I am having problems with the clothes remaining wet after cycle has completed. At times no agitation. I bypassed the cover switch so that is not the problem. A Tech checked it and said thd clutches are defective.it is a whirlpool commercial super capacity plus,9 cycles 5 speed combination. Quiet wash. White in colour. I need to get the model no. And any other relevant information. I really do not want to part with this machine.
Do you own this unit? Please describe repair issue you are having.
What is the Whirlpool Top Load Washer LSQ9200LQ tub capacity?
Tub Capacity as per Manufacturer Specifications (in cubic feet):
The manufacturers began using cubic feet capacity numbers only recently.
Previously, they used relative terms such as "Large" or "Extra Capacity" or laundry weight (e.g. "16 lbs per load")
which did not take into account different fabric weight and volume. Others referred to capacity in
terms of water used. Even washers available today do not have capacity written in the manual because the same manual
can be used across multiple models. Once the washer is no longer sold, the sales literature is discarded
and capacity information often lost.
Analyzing washers and their components, searching through old technical information and sales literature, and
determining their capacity is a labor intensive and time-consuming task and we are far from finished.
A small charge will help us continue our research.
Consider this: if you were to spend more than few minutes looking for tub capacity on the internet, you
would be earning LESS than minimum wage.
Calculate Washer Tub capacity
This is a geometric method to calculate tub capacity based on the cylinder volume formula.
Unfortunately, the value could be as much as 25% off from the manufacturer stated capacity.
Why? Because a tub is not exactly a cylinder. The edge where bottom connected to the wall
is not at 90 degree angle but smooth and rounded. The water line is not clearly marked and
the bottom is not always flat. Finally, an agitator also takes capacity away from the tub.
This method can be used as a crude estimate but we do not recommend using it for comparisson
when shopping for a new washer.
Determine your washer tub capacity by taking two simple measurements:
1. Use the ruler to measure the depth of the tub (indicated by the red line on the diagram)
2. Now find the distance accross the tub, the diameter (the green line on the diagram). Note that some tubs are narrow
at the opening. In this case make the measurements INSIDE the tub.
Tub Depth: in. Tub Diameter: in.
The Whirlpool Top Load Washer LSQ9200LQ tub capacity is cubic feet.
DOE (Department of Energy) vs. I.E.C. (International Efficiency Consortium) tub capacity values
The tub capacity calculator provides result in the DOE cubic feet which are CONVENTIONAL, i.e. normal cubic feet.
The front loading appliance manufacturers prefer to use IEC cubic feet in their specification. IEC capacity
in a front loader is the equivalent of the laundry size of a top loading washer and usually result in a higher number.
For instance, a 4.7 cu. ft EC capacity transaltes into 4.1 conventional cu. ft for some washers and into 4.2 cu. ft for others.
There is no simple multiplier that can be applied to an IEC value to translate it into DOE capacity.
Make sure to use the manufacturer's part number when ordering a replacement.